300-415 Exam - Implementing Cisco SD-WAN Solutions (ENSDWI)

NEW QUESTION 1
An engineer is configuring a data policy IPv4 prefixes for a site WAN edge device on a site with edge devices. How is this policy added using the policy configuration wizard?

• A. In vManage NMS select (he configure policies screen, select the centralized policy tab and click add policy
• B. In vBood orchestrato
• C. select the configure > policies screen select the localized policy ta
• D. and click add policy
• E. In vManage NM
• F. select the configure policies scree
• G. select the localized policy tab- and click add policy
• H. In vSmart controller select tie configure policies screen, select the localized policy tab, and click add policy

Answer: C

NEW QUESTION 2
Which protocol is used to propagate multicast join requests over the Cisco SD-WAN fabric?

• A. ARP
• B. Auto-RP
• C. OMP
• D. IGMP

Answer: D

NEW QUESTION 3
Which multicast component is irrelevant when defining a multicast replicator outside the local network without any multicast sources or receivers?

• A. PIM interfaces
• B. TLOC
• C. overlay BFD
• D. OMP

Answer: A

NEW QUESTION 4
What is the result during a WAN Edge software upgrade process if the version of the WAN Edge software is higher than the one running on a controller device?

• A. The upgrade button is greyed out
• B. The upgrade proceeds with no warning message.
• C. The upgrade fails with a warning message
• D. The upgrade proceeds with a warning message

Answer: D

NEW QUESTION 5
Refer to the exhibit.

A network administrator is configuring OMP in vManage to advertise all the paths for the same prefix from a site that has two WAN Edge devices Each WAN Edge device is connected to three ISPs and two private MPLS transports. What is the minimum value for 'Number of Paths advertised per Prefix" that should be configured?

• A. 2
• B. 3
• C. 5
• D. 10

Answer: D

NEW QUESTION 6
An engineer is configuring a data policy for IPv4 prefixes for a single WAN Edge device on a site with
multiple WAN Edge devices How is this policy added using the policy configuration wizard?

• A. ln vManage NMS, select the configure policies screen, select the localized policy tab and click add policy
• B. In vSmart controller, select the configure policies screen, select the localized policy ta
• C. and click add policy
• D. In vManage NM
• E. select the configure policies screen select the centralized policy tab and click add policy
• F. In vBond orchestrato
• G. select the configure policies screen, select the localized policy ta
• H. and click add policy

Answer: A

NEW QUESTION 7
Refer to the exhibit

An engineer is configuring a QoS policy to shape traffic for VLAN 100 on a subinterface Which policy configuration accomplishes the task?
A)

B)

C)

D)

• A. Option A
• B. Option B
• C. Option C
• D. Option D

Answer: C

NEW QUESTION 8
Which attributes are configured to uniquely Identify and represent a TLOC route?

• A. system IP address, link color, and encapsulation
• B. firewall, IPS, and application optimization
• C. site ID, tag, and VPN
• D. origin, originator, and preference

Answer: A

Explanation:
https://www.cisco.com/c/dam/en/us/td/docs/solutions/CVD/SDWAN/CVD-SD-WAN-Design-2018OCT.pdf

NEW QUESTION 9
Refer to the exhibit

An engineer must configure a QoS policy between me hub and site A (spoke) over a standard internet circuit where traffic shaping is adjusted automatically based on evaiiabk» bandwidth Which configuration meets the requirement?

• A. Option A
• B. Option B
• C. Option C
• D. Option D

Answer: D

NEW QUESTION 10
An engineer configures an application-aware routing policy for a group of sites The locations depend on public and private transports The policy does not work as expected when one of the transports does not perform properly This policy is configured:

which configuration completes the policy so that it works for all locations?
A)

B)

C)

D)

• A. Option A
• B. Option B
• C. Option C
• D. Option D

Answer: A

NEW QUESTION 11
Which plane builds and maintains the network topology and makes decisions on traffic flows?

• A. orchestration
• B. management
• C. control
• D. data

Answer: C

NEW QUESTION 12
Refer to the exhibit.

The control connection is failing. Which action resolves the issue?

• A. import vSmart in vManager
• B. Validate the certificates authenticity on vSmart
• C. Upload the WAN Edge list on vManage.
• D. Restore the reachability to the vSmart

Answer: D

Explanation:
https://www.cisco.com/c/en/us/support/docs/routers/sd-wan/214509-troubleshoot-control-connections.html

NEW QUESTION 13
An administrator is configuring the severity level on the vManage NMS for events that indicate that an action must be taken immediately. Which severity level must be configured?

• A. warning
• B. error
• C. critical
• D. alert

Answer: D

Explanation:

NEW QUESTION 14
An engineer creates a data policy to prevent communication from the 172.20.21.0/24 network to the 172.20.41.0/24 network. Which configuration accomplishes this task?

• A. Option A
• B. Option B
• C. Option C
• D. Option D

Answer: B

NEW QUESTION 15
An engineer wants to change the configuration of the certificate authorization mode from manual to automated. Which GUI selection will accomplish this?

• A. Maintenance > Security
• B. Configuration > Certificates
• C. Administration > Settings
• D. Tools > Operational Commands

Answer: C

Explanation:

NEW QUESTION 16
Which secure connection should be used to access the REST APIs through the Cisco vManage web server?

• A. HTTP inspector interface
• B. authenticated HTTPS
• C. authenticated DTLS
• D. JSON Inspector interface

Answer: B

Explanation:
https://documenter.getpostman.com/view/3224967/SVmpXhXd#ed9ccd34-cc5a-4258-bb6b-9b3848b7f650

NEW QUESTION 17
......