350-401 Exam - Implementing and Operating Cisco Enterprise Network Core Technologies

NEW QUESTION 1

What is a characteristics of traffic shaping?

• A. can be applied in both traffic direction
• B. queues out-of-profile packets until the buffer is full
• C. drops out-of-profile packets
• D. causes TCP retransmits when packet are dropped

Answer: B

NEW QUESTION 2
DRAG DROP
Drag and drop the tools from the left onto the agent types on the right.

• A. Yes
• B. Not Mastered

Answer: A

NEW QUESTION 3

How is Layer 3 roaming accomplished in a unified wireless deployment?

• A. An EoIP tunnel is created between the client and the anchor controller to provide seamless connectivity as the client is associated with the new AP.
• B. The client entry on the original controller is passed to the database on the new controller.
• C. The new controller assigns an IP address from the new subnet to the client
• D. The client database on the original controller is updated the anchor entry, and the new controller database is updated with the foreign entry.

Answer: D

NEW QUESTION 4

What is one difference between saltstack and ansible?

• A. SaltStack uses an API proxy agent to program Cisco boxes on agent mode, whereas Ansible uses a Telnet connection
• B. SaltStack uses the Ansible agent on the box, whereas Ansible uses a Telnet server on the box
• C. SaltStack is constructed with minion, whereas Ansible is constructed with YAML
• D. SaltStack uses SSH to interact with Cisco devices, whereas Ansible uses an event bus

Answer: C

NEW QUESTION 5
SIMULATION
Simulation 02
Configure HSRP between DISTRO-SW1 and DISTRO-SW2 on VLAN 100 for hosts connected to ACCESS-SW1 to achieve these goals:
* 1. Configure group number 1 using the virtual IP address of 192.168.1.1/24.
* 2. Configure DlSTRO-SW1 as the active router using a priority value of 110 and DISTRO- SW2 as the standby router.
* 3. Ensure that DISTRO-SW2 will take over the active role when DISTRO-SW1 goes down, and when DISTRO-SW1 recovers, it automatically resumes the active role.






DISTRO-SW2

• A. Yes
• B. Not Mastered

Answer: A

NEW QUESTION 6

How does EIGRP differ from OSPF?

• A. EIGRP is more prone to routing loops than OSPF
• B. EIGRP supports equal or unequal path cost, and OSPF supports only equal path cost.
• C. EIGRP has a full map of the topology, and OSPF only knows directly connected neighbors
• D. EIGRP uses more CPU and memory than OSPF

Answer: B

NEW QUESTION 7

Under which network conditions is an outbound QoS policy that is applied on a router WAN interface most beneficial?

• A. under interface saturation condition
• B. under network convergence condition
• C. under all network condition
• D. under traffic classification and marking conditions.

Answer: A

NEW QUESTION 8

Refer to the exhibit.

SwitchC connects HR and Sales to the Core switch However, business needs require that no traffic from the Finance VLAN traverse this switch Which command meets this requirement?
A)

B)

C)

D)

• A. Option A
• B. Option B
• C. Option C
• D. Option D

Answer: D

NEW QUESTION 9

Which two Cisco SD-WAN components exchange OMP information?

• A. vAnaiytlcs
• B. vSmart
• C. WAN Edge
• D. vBond
• E. vManage

Answer: BC

NEW QUESTION 10

Refer to the exhibit.

Clients are reporting an issue with the voice traffic from the branch site to the central site. What is the cause of this issue?

• A. The voice traffic is using the link with less available bandwidth.
• B. There is a routing loop on the network.
• C. Traffic is load-balancing over both links, causing packets to arrive out of order.
• D. There is a high delay on the WAN links.

Answer: C

Explanation:
Traffic is load-balancing over both links, causing packets to arrive out of order. This can cause voice quality issues, such as jitter and delay. To avoid this problem, voice traffic should be sent over a single path, using a routing protocol that supports unequal-cost load balancing, such as EIGRP. The source of this answer is the Cisco ENCOR v1.1 course, module 4, lesson 4.3: Implementing EIGRP.

NEW QUESTION 11

Refer to the exhibit.

Which privilege level is assigned to VTY users?

• A. 1
• B. 7
• C. 13
• D. 15

Answer: A

Explanation:
Lines (CON, AUX, VTY) default to level 1 privileges.

NEW QUESTION 12

When configuration WPA2 Enterprise on a WLAN, which additional security component configuration is required?

• A. NTP server
• B. PKI server
• C. RADIUS server
• D. TACACS server

Answer: C

NEW QUESTION 13

Refer to the exhibit.

An engineer deploys a script to retrieve the running configuration from a NETCONF- capable Cisco IOS XE device that is configured with default settings. The script fails. Which configuration must be applied to retrieve the configurauon using NETCONF?

• A. Print (netconf_host.get_config('show running'!)
• B. hostkey_verify=True,
• C. device_params={name':'ios-xe'})
• D. port=830

Answer: A

NEW QUESTION 14

A network engineer must configure a switch to allow remote access for all feasible protocols. Only a password must be requested for device authentication and all idle sessions must be terminated in 30 minutes. Which configuration must be applied?

• A. Option A
• B. Option B
• C. Option C
• D. Option D

Answer: C

NEW QUESTION 15

In a Cisco SD-Access wireless architecture which device manages endpoint ID to edge node bindings?

• A. fabric control plane node
• B. fabric wireless controller
• C. fabric border node
• D. fabric edge node

Answer: A

Explanation:
SD-Access Wireless Architecture Control Plane Node –A Closer Look Fabric Control-Plane Node is based on a LISP Map Server / Resolver
Runs the LISP Endpoint ID Database to provide overlay reachability information
+ A simple Host Database, that tracks Endpoint ID to Edge Node bindings (RLOCs)+ Host Database supports multiple types of Endpoint ID (EID), such as IPv4 /32, IPv6 /128* or MAC/48+ Receives prefix registrations from Edge Nodes for wired clients, and from Fabric
mode WLCs for wireless clients+ Resolves lookup requests from FE to locate Endpoints+ Updates Fabric Edge nodes, Border nodes with wireless client mobility and RLOC information

NEW QUESTION 16

Refer to the exhibit. What is the result of this Python code?

• A. 1
• B. 7
• C. 7.5

Answer: D

Explanation:
The Python code in the exhibit defines a function called average that takes two parameters a and b and returns the arithmetic mean of them. The function is then called with the arguments 5 and 10, which are assigned to a and b respectively. The function returns (5 + 10) / 2, which is 7.5. Therefore, the result of the Python code is 7.5. References: Python Functions, Python Arithmetic Operators

NEW QUESTION 17

Which solution should be used in a high-density wireless environment to increase bandwidth for each user?

• A. Increase antenna size
• B. Increase the mandatory minimum data rate.
• C. Increase the cell size of each AP.
• D. Increase TX power.

Answer: B

NEW QUESTION 18

Which outbound access list, applied to the WAN interface of a router, permits all traffic except for http traffic sourced from the workstation with IP address 10.10.10.1?
A)

B)

C)

D)

• A. Option A
• B. Option B
• C. Option C
• D. Option D

Answer: A

NEW QUESTION 19
......